Skip to main content

How We Get Our Numbers

Where the BTU, weight and seasoning figures for all 70 species come from, how we sanity-check them, and the exact math behind every calculator on the site.

Where do the BTU numbers come from? Short answer:

Every BTU figure is million BTU per full cord (128 cubic feet) of wood dried to about 20% moisture. They’re compiled from published firewood heat-value tables built on USDA Forest Products Laboratory wood density data and university extension firewood charts, then cross-checked against each species’ dry weight per cord.

What the BTU Number Means

A BTU (British Thermal Unit) is the heat it takes to warm one pound of water by one degree Fahrenheit. When the BTU chart says red oak is 22.1, that means about 22.1 million BTU of heat in one full cord of seasoned red oak. Across our 70 species the range runs from 11.6 to 30.0 million.

That’s the heat in the wood, not the heat that ends up in your living room. How much of it you actually get depends on your stove, which is why the heating calculator divides by stove efficiency (more on that below). It also assumes the wood is properly dry. Burn it green and a big chunk of that heat goes into boiling off water.

Where the Data Comes From

Heat in firewood comes down to how much wood fiber is packed into the stack. Pound for pound, dry wood from different species holds a pretty similar amount of energy. Dense species win because a cord of them weighs more. So the backbone of every number on this site is wood density.

  • Wood density and heat content: the USDA Forest Products Laboratory’s Wood Handbook: Wood as an Engineering Material (General Technical Report FPL-GTR-282), the standard reference for the physical properties of North American wood species.
  • BTU per cord, seasoning and burn characteristics: university extension firewood guides, which turn that density data into per-cord heat values and add practical notes on splitting, smoke and drying.
  • Climate (heating degree days): NOAA climate normals, summarized by 3-digit ZIP code prefix for the heating calculator.

How We Sanity-Check Every Species

Because heat tracks weight, every species gets lined up against its own dry weight per cord. For most of the hardwoods on this site the BTU figure works out to roughly 6,200 BTU for every pound of dry wood in the cord. That gives us a quick way to catch typos and bad source data: a species that lands way outside that band gets a second look against the sources.

Some species legitimately run high. Resin carries more energy than plain wood fiber, so pitchy softwoods like pinyon pine come out ahead per pound even though they’re lighter. That’s expected, not an error.

Dry weight is pounds per full cord at about 20% moisture. Green weight, where we have it, is the same cord freshly cut. The gap between the two is the water you’re waiting on while it seasons.

Seasoning Times

Seasoning times are the months it takes wood to get under 20% moisture, given as a range because real life varies. They assume the wood is cut to length, split, stacked off the ground with the sides open to the wind, and covered on top. Dense species and species that hold a lot of water when green sit at the long end.

Your climate matters a lot. A sunny, windy spot in a dry climate can beat the low end of the range. A shady, humid backyard or unsplit rounds can blow way past the high end. That’s why we always say check it with a moisture meter instead of trusting the calendar. See every species on the seasoning time chart.

Burn Ratings (Smoke, Sparks, Coals, Splitting)

Smoke, sparks, coal quality, split difficulty and smell are rated on simple scales (for example few / moderate / many sparks). They come from extension firewood charts and widely reported burning experience for each species, assuming seasoned wood. Wet wood of any species smokes and sizzles, so the ratings won’t match green wood.

The overall rating (poor, fair, good, excellent) is a judgment call that weighs all of it together: heat per cord, coals, how much work it is to split and season, and how clean it burns.

The Heating Calculator Math

The heating calculator estimates how many cords you’ll burn in a season with two formulas:

Heat needed (BTU) = square feet × insulation factor × heating degree days ÷ stove efficiency
Cords = heat needed ÷ BTU per cord of your species
  • Heating degree days come from your ZIP code. We map 938 three-digit ZIP prefixes to typical annual heating degree days.
  • Insulation factor is BTU per square foot per degree day: poor 12, below average 9, average 7, good 5, excellent 3.
  • Stove efficiency is the share of the wood’s heat that makes it into the house: open fireplace 10%, non-airtight stove 25%, fireplace insert 40%, convective fireplace 40%, airtight stove 55%, EPA-certified wood stove 72%, wood gasification boiler 80%, pellet stove 85%, masonry heater 90%.

It’s an estimate for a full heating season with wood as the main heat source. Lifestyle (how warm you keep the house, how much you lean on a backup furnace) moves the real number around, so treat it as a planning number and buy a little extra.

Cord Measurements

A full cord is 4 × 4 × 8 feet, 128 cubic feet. A face cord (or rick) is 4 × 8 feet by one row deep, which is one third of a cord with 16-inch pieces. A full-size pickup stacked level holds about half a cord. The cord calculator uses exactly those conversions.

Updates and Corrections

When we change a number, the species page and every calculator that uses it update together, since they all read from the same data. If a number looks off compared to what you’ve seen in your own stove, we want to hear about it.

Last reviewed: